Powerpole Distribution: Difference between revisions
From SUWS-wiki
No edit summary |
|||
| Line 1: | Line 1: | ||
{{Project | {{Project | ||
|Title=Powerpole Distribution Box Project | |Title=Powerpole Distribution Box Project | ||
|Status= | |Status=Completed | ||
|Project Lead=User:TylerWard | |Project Lead=User:TylerWard | ||
}} | }} | ||
| Line 12: | Line 12: | ||
=== Status === | === Status === | ||
* | * Completed, designs are available at [https://github.com/Tyler-Ward/Powerpole-distribution-board Github] | ||
=== Feature List === | === Feature List === | ||
| Line 40: | Line 39: | ||
| LED || 3mm red/yellow || £0.24 for each || [http://onecall.farnell.com/kingbright/l-937eyw/led-3mm-he-red-yel/dp/1142490] | | LED || 3mm red/yellow || £0.24 for each || [http://onecall.farnell.com/kingbright/l-937eyw/led-3mm-he-red-yel/dp/1142490] | ||
|- | |- | ||
| PCB || 5*10cm 2oz blue || $40.95 for ~10 or (£3 each) || [dirtypcbs.com] | | PCB || 5*10cm 2oz blue || $40.95 for ~10 or (£3 each) || [http://dirtypcbs.com] | ||
|} | |} | ||
Revision as of 14:11, 27 May 2016
| Powerpole Distribution Box Project | |
|---|---|
| [[File:|250px|Powerpole Distribution Box Project]] | |
| Status | Completed |
| Project Lead | User:TylerWard |
Powerpole Distribution Box Project
Powerpole Distribution Box Project
Status
- Completed, designs are available at Github
Feature List
- 6 power-pole connectors
- Individually fused connections with indicators
- 30A+ capacity (Limited by current rating of the fuse holders)
Costings
Costings below are for individual orders the main club order will be cheaper
| Type | Item | Cost | Link |
|---|---|---|---|
| connector | 12*45A pcb contacts | £9.90 for 15 | [1] |
| connector | 6* red 45A housings | £2.65 for 10 | [2] |
| connector | 6* black 45A housings | £2.65 for 10 | [3] |
| Fuseholder | Keystone 3522 | £6.56 for 100 | [4] |
| Resistor | 330ohm though hole 0.25w | £0.23 for 10 | [5] |
| LED | 3mm red/yellow | £0.24 for each | [6] |
| PCB | 5*10cm 2oz blue | $40.95 for ~10 or (£3 each) | [7] |
Build instructions
Tools Required
- Soldering Iorn (Should be a high power Iron (45W+) with a large tip do that it has a large thermal mass)
- Sidecutters
- (Usefull) Helping hands or other PCB support tool.
Instructions
- Solder resistors capacitors and LEDs onto the PCB.
- Push Fuse holder contacts into pcb
- Solder Fuse holder contacts, these will suck up the heat so might take a bit to get up to temperature.
- Assemble to top two case layers and attach the partly populated PCB
- Assemble the powerpole contacts by joining them together and inserting the contacts.
- Place the powerpole contacts into the board.
- Solder the powerpole contacts on the board, I found the best way to do this is to push the board and contacts down onto a heatproof surface so that they sit in the correct place and then solder, these should be soldered fairly quickly as the powerpole housings can be melted if exposed to to much heat.
- Check for any solder bridges across the fuses or powerpoles.
- Assemble the remaining two layers of the case.
- Enjoy your Distro
